MUGM MunEDA User Group Meeting Selected Papers

Contact us to receive more information about your interesting case.

  • Innovative Design Methodology for Analog-to-Digital and Digital-to-Analog Converters
  • Structured and Automated Analog/Mixed-Signal IC Design for Automotive Electronics
  • Dependent Simulations for Trimming – Robustness verification for trimmed references
  • Automatic Initial Sizing of Operational Amplifiers with Weak, Moderate and Strong Inversion
  • Modeling Circuits with Parameter Variation
  • Topology Migration of Sigma-Delta ADCs
  • Analog IP Migration between process technologies
  • Intelligent IP Fast Analog IC Design and Migration Using Generators
  • Corner Verification and Design Optimization in Smart Power Technologies
  • Effective analog circuit design using optimization tools
  • Power Optimization for LO Buffers and PA+matching in a low-power SoC
  • Using Circuit Optimization in Flash Applications
  • Design Optimization and Retargeting Strategies of Standard Cells in 28nm FDSOI Technology
  • High-Sigma Verification of SRAM cells
  • Power-Down Synthesis for Analog Circuits
  • A Generic Topology Selection Method of Analog Circuits with Embedded Circuit Sizing Demonstrated on OTA Example
  • Optimization of a Low-power Fully Differential OTA and an Introduction to Modelling the Performance Space of Front-ends for Thermoelectric Sensor Arrays

2018

2017

  • Read Path Optimization for 40nm Technology
  • Optimization and Evaluation of Interface Circuits
  • SRAM Hierarchical Read Failure Analysis
  • Fail analysis of Digital Temperature Sensors in Non-Volatile Memory
  • Optic Simulation Solutions in High End Devices
  • Robustness Optimization for MEMS-IC Systems
  • ULTRA-LOW-VOLTAGE (ULV) IC DESIGN: DESIGNING FOR VDD BELOW kT/q
  • Low Power Optimization for Robustness
  • Application of a trimming flow
  • Trade-off analysis between Area and Yield/Robustness
  • Circuit Design Optimization for Radiation Hardening
  • Design optimization of voltage buffer and reuse of IP

2016

2015

  • Optimization for extreme low power dissipation of bandgap designs with WiCkeD
  • Hierarchical SRAM worst case analysis
  • Fail analysis for bandgap reference in nonvolatile memory
  • Reliability aware design in FDSOI technologies
  • Optimization of Settling Time and Stability for a Low-power Fully-differential Operational Amplifier
  • Optimal NBTI Degradation and PVT Variation Resistant Device Sizing in a Full Adder Cell
  • Process related yield debug and optimization of analog IP
  • Sign-off Flow for RF Applications in a 65nm Technology
  • S&H Sample & Hold (ADC) Mismatch Analysis and Sizing
  • I/O Design Optimization Flow for Reliability In Advanced CMOS Nodes
  • IO circuit optimization to enhance productivity, circuit robustness and reliability
  • Design validation and development of RF macrocells
  • Safeguarding Holdtime Margin for Internal Scan Chain in Multibit-Register Standardcells
  • 55nm to 40nm Bandgap porting with SPT & High gain Amp optimization
  • Full-Semi-custom Clock Trees Optimization – Clock Skew Matching, Insertion Delay, Duty-Cycle

2014

2013

  • Power and performance optimization with transistor variables on custom circuits
  • Effects of Process Variation and Mismatch on Circuit Design: Monte Carlo and Alternatives
  • Process Characterization in 40nm and Level Shifter Optimization in 65nm (RF Design)
  • Verification and Optimization of Digital Radio Receiver Sub Circuits
  • Noise and performances analysis of a 180 nm CMOS OPAMP
  • NAND Flash Cell Sensing Sensitivity Analysis & Improvement
  • Standard Cell Performances Optimization & High Sigma Yield Analysis
  • AutoScript based design optimization flow setup for FinFET high-speed memory interfaces
  • Low Power MPSoC Circuit Design in GLOBALFOUNDRIES 28nm CMOS
  • Corner parameter generation
  • Sizing of FPGA cells with Least Squares Fitting
  • FPGA Routing Driver Optimization and SRAM sense amp optimization
  • Sizing of standard cells in worst-case process conditions in 110nm BCD
  • Verification and Optimization of Digital Radio Receiver Sub Circuits
  • Automated Analog Synthesis-driven Process Technology Exploration

2012

2011

  • Reducing Mismatch Impact by means of Proper Biasing in Fully Differential, Low Power CMOS Structures
  • Analog Design Optimization with gm-ID Lookup Table Method
  • PLL Loop Optimization
  • Analysis Method for Parasitic RC Variation
  • Mismatch Sizing and Corner Verification for Automotive Applications
  • IP Porting and Resizing for High-Speed NoC
  • Schematic Porting with Symbol Adaption and Initial Sizing as Pre-Process for Optimization
  • Design Optimization for Sensing Circuit of Resistive Memory
  • Optimization of a 2.133GHz level shifter in 28nm
  • Parameter Calibration and Cascaded Simulations
  • Surrogate models for the analog circuit simulation based on a machine learning approach
  • Exploration of Feasible Voltage Ranges in Analog CMOS Circuits Using Linearized-Operating-Point Transistor Models
  • Performance & Yield Optimization of a Switched DC/DC Converter in 350nm Technology
  • Embedded Flash memory Vx Linear Regulator porting from 90nm to 55nm technology while improving regulation accuracy to solve yield weakness
  • Voltage Generator Fail Analysis & Issue Clear with f-DFM
  • Multi-Testbench Analysis and Optimization of an LNA for AM radio receiver in 65 nm CMOS technology
  • Extraction Methods of VHDL/VerilogA Models for Analog Blocks, Usable Inside Time Domain Simulations

2010

2009

  • Worst Case Analysis and Yield Optimization of a micro-power precision OpAmp based on an advanced Offset Cancellation Chopper technique in 350nm
  • Design and characterization of a dither VCO for mixed signal application at different levels of abstraction
  • Modelling of Multi-Stage Amplifiers
  • Architectural Assessment of Design Techniques to Improve Speed and Robustness in Embedded Microprocessors
  • Ring oscillator in 65nm non volatile memory technology for low emission I/O pad buffer in 90nm CMOS low power technology for Car Radio applications
  • Design and Optimization of a High-Speed Blu-ray Disc Photodetector IC
  • Statistical Analysis and Optimization of a Sense Amplifier for very low voltage applications in CMOS 90nm Flash technology
  • Circuit Design Optimization Cases for Wireless Cellular Communication
  • Considering Parameter Variations in IC Design Optimization: Pareto-front Calculation
  • Response surface modelling for Industrial Application Cases
  • Digital Timing and Power Simulation with Statistical Process Variations
  • High Reliable design for High-Performance Analog Circuits

2008

2007

  • Optimization and Centering of the Basic Cells of SRAM Memories
  • Analysis and Optimization of a CMOS Mixer Circuit
  • Optimization of I/O Macro Cells
  • Robust and Reliable Analog Design for Automotive and Sensor Applications by Combining Design Centering and SOA Techniques
  • Automatic Analog Circuit Synthesis
  • Hierarchical Optimization for Phase-Locked Loops (PLL) considering Jitter, Power and Locking Time
  • 6T for Embedded SRAM – six sigma design
  • Reuse of Circuit Topologies
  • Design for Manufacturing (DFM) reference design flow
  • Circuit Design for Yield (DFY) for a 110dB Op-Amp for Automotive and Sensor Applications

2006

Contact us to receive more information about your interesting case.

Let’s work together on your
next design project

Use MunEDA tools and support to speed up efficiency,
quality and outcome of your next circuit design project